Hidrosadalītājs paredzēts Doosan HD1430 midi ekskavatora
Ja Jūs esat nolēmuši iegādāties tehniku par zemu cenu, pārliecinieties, ka sazināties ar reālo pārdevēju. Uzziniet pēc iespējas vairāk informācijas par tehnikas pārdevēju. Viens no krāpniecības veidiem - uzdot sevi par reāli eksistējošu kompāniju. Ja jums ir radušās šaubas, sazinieties ar mums papildus kontroles veikšanai, izmantojot atsauksmju formu.
Pirms jūs izlemjat veikt pirkumu, uzmanīgi izskatiet vairākus pardošanas piedāvājumus, lai saprast vidējo cenu jūsu izvēlētajam tehnikas modelim. Ja piedāvājuma cena ir daudz zemāka kā analoģiskiem piedāvājumiem, aizdomājieties. Liela cenu starpība var būt saistīta ar slēptiem defektiem vai ar pārdevēja mēģinājumu veikt krāpnieciskas darbības.
Nepērciet preces, kuru cena atšķiras no vidējās cenas uz analoģisku tehniku.
Nepiekrītiet abšaubāmām ķīlām un preces priekšapmaksai. Šaubu gadījumā nebaidieties precizēt detaļas, palūgt papildus fotogrāfijas un dokumentus uz tehniku, pārbaudiet dokumentu autentiskumu, uzdodiet jautājumus.
Pats populārākais krāpniecības veids. Negodīgie pārdevēji var pieprasīt noteiktu avansa summu, lai "rezervēt" jūsu tiesības uz tehnikas pirkumu. Tādā veidā krāpnieki var savākt lielu naudas summu un pazust, bez kontakta iespējām ar viņiem.
- Priekšapmaksas pārskaitījums uz karti
- Neveiciet preikšapmaksu bez dokumentu noformēšanas, kas apstiprina naudas nodošanas procesu, ja komunikācijas laikā jums rodas šaubas par pārdevēju.
- Pārskaitījums uz "pilnvarotas personas" kontu
- Šādam lūgumam ir jārada bažās, visdrīzāk jūs kontaktējaties ar krāpnieku.
- Pārskaitījums uz kompānijas kontu ar līdzīgu nosaukumu.
- Esiet uzmanīgi, krāpnieki var maskēties zem populārām kompānijām, ieviešot nelielas izmaiņas nosaukumā. Nepārskaitiet naudu, ja nosaukums izraisa šaubas.
- Savu rekvizītu ievietošana reāla uzņēmuma rēķinā
- Pirms veikt apmaksu, pārbaudiet, vai norādītie rekvizīti ir korekti un vai tie attiecas uz norādīto uzņēmumu.
Pārdevēja kontakti
+86 189 289...
+86 189 2896 5241
Product Overview
A 30‑ton class crawler excavator is bought for one quality above all others: authority. It should push through a stockpile without stalling, lift a loaded bucket off a bench without hesitation, and hold that load while the truck pulls under it. That authority comes from hydraulic pressure reaching the cylinders intact — and the main control valve is the component that either delivers it or lets it leak away. On the HD1430, the block divides pump flow among boom, arm, bucket, swing and travel, and everything the operator feels at the levers passes through it.
When the block wears, the machine loses authority before it loses function. Nothing breaks; the machine simply stops pushing as hard. The boom sags on a held bucket. The arm labours into a pile. Swing placement lands short. Tracks bog down when the bucket is loaded. Operators compensate by working the levers longer and running the engine harder, which raises heat and fuel burn without restoring the lost force. The cause is internal leakage past worn spools. This aftermarket main valve replaces the assembly complete with fresh internals set to working pressure values, so the worn unit unbolts as one piece and the replacement goes into the original hose positions.
Core Advantages
1. Restores the push a 30‑ton machine is bought for
Worn spools bleed pressure before it reaches the cylinders. Fresh clearances put the force back, so the machine works through a pile instead of labouring at it.
2. Stops the compensation that raises heat and fuel
Operators work harder to make up for lost force. Once the block holds pressure properly, the machine does the same work at normal throttle.
3. Loads stay put while the truck pulls away
A boom that sags on a held bucket forces a re‑spot every pass. Renewed pressure retention keeps the load where it was placed.
4. Swing placement lands first time
Restored circuit isolation ends the overshoot‑and‑hunt habit, which matters on loading cycles where seconds repeat hundreds of times a shift.
5. Complete assembly rather than open‑ended repair
One tested block resolves every circuit that has drifted, instead of returning to the machine for one failure after another.
Manufacturing & Quality Control
Spool and bore pairs are machined to drawing tolerance, matched by size, and hand‑run‑in until travel across the full stroke is free of binding. Assembled blocks are flow‑tested circuit by circuit, with relief and compensator values recorded before release; units outside window are stripped and corrected. Blocks ship internally oil‑fogged, ports capped, and crated on foam.
Frequently Asked Questions
Q1: How do I confirm this block suits my machine?
A: Send the machine serial plate and photos of the existing valve, including the port layout and mounting face. The HD designation appears across several builders and build years, so we match on configuration rather than the name alone.
Q2: What symptoms indicate valve wear rather than pump wear?
A: Loss of force on held loads, slack at stroke start, inconsistent swing and load‑dependent tracking point to the valve. Uniform slowness with hot oil points to the pump. A circuit leak test separates them.
Q3: Can the existing block be rebuilt?
A: If the casting is sound and has never been rebuilt, a kit may restore it. Where wear spans several circuits, a complete assembly is usually the better long‑term cost. Photos help us advise.
Q4: What hydraulic servicing accompanies installation?
A: Flush the system, renew the return filter or filters, clean the suction strainer, and refill with specified oil. Contaminated oil will damage new clearances within weeks.
Q5: How much downtime should be planned?
A: Most of a working day for removal and refit with the cover open on a machine this size, plus bleeding and pressure verification. Schedule it as a planned stop.
Q6: What is excluded from warranty?
A: Material and assembly faults are covered. Damage from dirty oil, water ingress, a spool forced against a bind, or reliefs altered outside specification is not. Photograph the crate before opening if damage is visible.